hayward flow switch troubleshooting

Check out the Sundance Spas Flow Switch Replacement if you are looking for the flow switch replacement for your Sundance Spa Jacuzzi. 14-17 Changing the Default Reading Pg.

Hayward Goldline Replacement Flow Switch Glx Flo Rp

Plug the cable back in and check the valve again.

. 3 LowHigh Cell Temperature Pg. 6 month manufacture parts only warranty when purchased through a Hayward Authorized Online Reseller. If the No Flow LED is ON check if the flow switch is installed backward.

Should be no elbow after the flow switch. Push the diagnostics button until t - 15 t - 9 t -5 t - 3 appears. While you are checking the valve position check the valve to make sure there are no obstructions.

Reliable durable Hayward pumps will still likely need some type of troubleshooting at some point during your relationship. Return switch to AUTO. The blower will turn off for one second.

If you are troubleshooting problems with the cooling cycles of a heatcool unit the following charts cover the majority of issues. The Control checks for a closed Blower Vacuum Switch. Flow Switch Assembly GLX-FLO-RP for HaywardGoldline Aquarite Salt Systems Pool Flow Sensor Suitable for Hayward Salt Cell and Salt Chlorine Generator System with 15-Foot Cable.

Continuity is open if there is no flow. Gas valve opens and monitors flame sense. The majority of our literature and brochures are in English only.

We carry the other brands but Hayward pumps and filters have always been our flagship line. Super Chlorinate Auto Off Super Chlorinate Auto. No LEDsLCD display verify 220-240 VAC or 115-125 VAC.

45 out of 5 stars. Check that the flow line is plugged all the way into the control box. Troubleshooting cooling cycles of a heatcool unit.

If it is not open disconnect the cable and wait for six seconds. Darrin - If you held the switch contacts closed for 60 seconds and the No Flow LED did not go off your new switch may be bad. Start with the main toggle switch in the Auto position.

A Sensor Blocks SENS 1-4 J Flow Switches FLOW 1-2 S 120VAC to Power Supply B Turbo Cell Low Voltage Relays LVR 1-4 K CHLR1 T Rectifier Inputoutput AC to DC Cell C Valve Actuators VLV 1-4 L WiFi Antenna LAN Power U 20A Fuse Protects Cell Circuit D 2 4 -wire Comm Bus M Relay Bank HVR 5 8 V Transformer Output 24VACCell Circuit. The Hayward Aqua Trol is a saltwater generator for above ground pools. The arrows at the top of the hex nut need to point in the same direction as the water flow.

There should be no elbow pipe after the flow switch. If this does not work turn the unit off again before trying any other troubleshooting techniques. If you have questions regarding troubleshooting a problem installing this flow switch call 1-888-921-7665 for Technical support.

1 No Lights with a Display Pg. Turns out some of these flow switches have misprinted directional arrows. Then give Hayward a call at 866-772-2100 to see what they say.

If there is adequate flow and the LED is still on check that the arrows on the flow switch on top of hex are pointing in the direction of flow. 19-21 How to Set Cell Type Pg. This flow switch is NOT compatible with any above ground spas.

No Flow LED will be ON when there is a flow switch problem. If you need help troubleshooting the device read our helpful guide with the most frequently asked questions and answers. 13 Switching from Metric to US Standard Pg.

Hayward Flow Control has been a leading manufacturer of industrial thermoplastic valves and process control products for more than 60 years. The flow switch requires a minimum flow rate of 11 GPM to consistently stay closed. Table of Contents Important safety instructions Pg.

In fact Hayward was one of the originators of the first thermoplastic ball valves. Hayward Goldline SuperPro Flow Switch Salt Generator Systems Q12DS156MNO3A. Troubleshooting flow charts.

Repeat until display shows correct cell. If anything is stuck in the valve holding it open the unit will not work properly. Hayward Aqua Rite Troubleshooting Guide.

Power Generating Super Chlorinate Remotely Controlled -r No Flow Cheek Salt High Salt nSpect Cell If LED is ON check for flow switch installed backward. No Flow LED will flash for up to 60 seconds on start-up. You can test the continuity of the flow switch using a Voltmeter or Ohmmeter.

That test bypasses tests for low flow and arrows installed wrong. 18 Check SaltInspect Cell LED flashing or ON Pg. Hayward AqauRite Parts - httpbitly38uhdcpTeflon Tape - httpbitly38tErzwTroubleshooting Your Hayward Aqua Rite System -.

Often what appears to be a pool pump problem is actually a filter problem or a valve problem so the first step is to rule out any mis-aligned valves or. If the flame is sensed The Blower Vacuum Switch Control Loop Temp. To change cell type cycle slide switch up to Super Chlorinate.

HAYWARD To switch Cell Type cycle Main Switch from AUTO- super Chlorinate AUTO. 4-5 Cell Cleaning instructions Pg. 3200 t-15 t-3 t-9 1Step 2 Step 3 Step 4.

The Igniter is de-energized at flame sense or at completion of 4 sec trial. Flow Switch for Hayward Salt Chlorine Generator GLX-FLO-RP with 15-Feet CableFlow Sensor with Tee Replacement Kit Suitable for Hayward Salt System 46. Since then we have remained committed to producing the highest quality products while providing outstanding service.

2 Display Only Lights Only or Neither Pg. Troubleshooting Guides To view these documents you will need to download the free Acrobat Reader which gives you instant access to PDF files. Installs in flow switch tee 401-247 Manufactured by Harwil and comes with a 15ft cord.

GLX-FLO-RP Flow switch is factory original The GLX-FLO-RP screw into your existing tee and comes with a 15 cord. Arrows at the top of the hex nut need to point in the direction of water flow. This generic replacement for the Hayward Goldline flow switch is relatively easy and will quickly fix your no-flow problem.

If you are unable to resolve or determine a problem additional info can be obtained by contacting the HAYWARD Service Department. At proper Igniter temp a 4 second trial begins. Green the above mentioned status indicates that your flow switch is stuck in close position or the wire is shorted andor the wire connections to the RJ11 modular phone connector is shorting out.

Ensure the flow switch valve is open.

How To Troubleshoot A Hayward Aqua Rite Inyopools Com